Instruction ManualRADIX Electronic Vertriebs-GmbH • D-61381 Friedrichsdorf • F.R. GermanyRead this instruction manual through carefully first. • Keep
Installing the ReceiverPage 10 Version 1.05 Installing the Receiver5.1 Prerequisites and Ambient ConditionsNOTE:Keep the receiver well away from sou
Installing the ReceiverVersion 1.0 Page 115.2.1 Single-Antenna Operation5.2.2 Dual-Antennae OperationGBAC95~265V50Hz MAX30WRF INPUT+13V/+18V400mA MAX.
Programming and Operating the Analog-Receiver SectionPage 12 Version 1.06 Programming and Operating the Analog-Receiver Section• Switch the receiver
Programming and Operating the Analog-Receiver SectionVersion 1.0 Page 136.2 Preselecting Channels from the Main Menu (Display Page 1)• Press the MEN
Programming and Operating the Analog-Receiver SectionPage 14 Version 1.06.3 Preselecting Channels from the Main Menu (Display Page 2)• Press the q
Programming and Operating the Analog-Receiver SectionVersion 1.0 Page 156.4 Preselecting Channels from the Main Menu (Display Page 3)The settings of
Setting Up and Programming the Digital ReceiverPage 16 Version 1.07 Setting Up and Programming the Digital Receiver7.1 Switching On the Receiver•
Setting Up and Programming the Digital ReceiverVersion 1.0 Page 177.2 Language Selection• Use the p and q keys to highlight the “Language”field, as s
Setting Up and Programming the Digital ReceiverPage 18 Version 1.07.4 Setting Decoder StatusSelecting the TV Aspect Ratio:• Use the p and q keys to
Setting Up and Programming the Digital ReceiverVersion 1.0 Page 19• Press the MENU-key.• Use the p and q keys to highlight the “OLD” DiSEqC-setting.
IntroductionPage 2 Version 1.01 IntroductionCongratulations on your decision to purchase a RADIX digital satellite receiver. All of ourmanufacturing
Setting Up and Programming the Digital ReceiverPage 20 Version 1.0The displayed data concerns the revision of the decoder firmware current at thetime
Setting Up and Programming the Digital ReceiverVersion 1.0 Page 217.5.2 Adjusting the DiSEqC-Controller and/or the 22-kHz Control SignalNOTE:This adj
Setting Up and Programming the Digital ReceiverPage 22 Version 1.07.5.3 Entering the Low-Noise Block (LNB) Converter’s Local-Oscillator FrequencyCom
Setting Up and Programming the Digital ReceiverVersion 1.0 Page 23• Cautiously realign the antenna until the triangular figure reachesmaximum size.Yo
Setting Up and Programming the Digital ReceiverPage 24 Version 1.07.6 Manual Channel Preselection7.6.1 Entering the Downlink FrequencyOnce the setti
Setting Up and Programming the Digital ReceiverVersion 1.0 Page 257.6.2 Entering the Symbol Rate• Use the p and q keys to highlight the “Symbol Rate
Setting Up and Programming the Digital ReceiverPage 26 Version 1.07.6.4 Conducting a Manual SearchOnce the settings of Sections 7.6.1 through 7.6.3,
Operating the Digital ReceiverVersion 1.0 Page 278 Operating the Digital ReceiverOnce all of the above settings have been made, your receiver will be
Operating the Digital ReceiverPage 28 Version 1.08.3 Using Channel DirectoriesDue to the large number of digital television channels, channel direct
Operating the Digital ReceiverVersion 1.0 Page 29Moving Channels:• Use the t and u to highlight the “Move” field.• Press the MENU-key to confirm you
ContentsVersion 1.0 Page 32 ContentsSection Title Page1 Introduction 22 Contents 33 Safety Precautions 54 The Receiver and Its Operation 64.1 The Remo
Operating the Digital ReceiverPage 30 Version 1.0• Use the p and q keys to highlight the channel to be deleted.• Press the MENU-key. The channel i
Operating the Digital ReceiverVersion 1.0 Page 318.4 Adjusting the Volume of the Sound Track/Muting• Press the MUTE-key to mute the sound track.• E
Operating the Digital ReceiverPage 32 Version 1.0• Use p and q keys to select the language desired.• Press one of the t or u keys to highlight the
Operating the Digital ReceiverVersion 1.0 Page 33This information largely consists of programming schedules, along with additionalinformation provided
Programming the Remote ControlPage 34 Version 1.09 Programming the Remote ControlThe remote control may be programmed using two different methods, e
Troubleshooting TipsVersion 1.0 Page 35Step 4: Press the SET-key to save the setting. The red LED willblink three times and then be extinguished.If n
ContentsPage 4 Version 1.08 Operating the Digital Receiver 278.1 Switching On the Receiver 278.2 Channel Selection 278.3 Using Channel Directories 28
Safety PrecautionsVersion 1.0 Page 53 Safety PrecautionsThis receiver is intended exclusively for the reception of satellite broadcasts, and should be
The Receiver and Its OperationPage 6 Version 1.04 The Receiver and Its Operation4.1 The Remote ControlNumerical KeysCursor-Control Key (cursor up)C
The Receiver and Its OperationVersion 1.0 Page 7Key Function During:Marking(s) Color Operation
The Receiver and Its OperationPage 8 Version 1.0Key Function During:Marking(s) Color Operation
The Receiver and Its OperationVersion 1.0 Page 94.2 The Receiver UnitControls and displays on the receiver’s front panelConnectors on the receiver’s
Commentaires sur ces manuels